Build 30 Ft Continuous Beam From 2x Lumber
How to Splice a Deck Beam Over a Support Post
It is always best to use a continuous beam without seams for higher strength. Dimensional lumber is readily available in lengths up to 20' which should accommodate a seamless beam for most applications. However, if your span is greater than 20' (like the image below) you will likely need to splice some boards to form a beam. In order to do this you should overlap the individual parts of the beam so they are staggered if possible. It is best to have one continuous board over a post allowing one joint to fall on top of the post. Overlapping seams integrates strength and prevents fracturing along seams throughout the length of the beam. Always split a beam over a post.
Plan ahead and layout the beam on the ground over the footings before installation. For instance you could use 2-2x10x10's and 2-2x10x20's to form a 30' beam with one seam set above two intermediate posts. You can also use hardware applications like strap ties or nailing plates to further secure the connection. Because these connectors are not particularly attractive you will probably want to conceal them behind fascia or on the interior side of the beam.
When attaching the first half of the beam to the notched 6x6 support post screw through the center of the 2x10. This will hold the 2x10 in place until you install the second 2x10 piece of the beam.
Drill 2 thru holes on the edges of each beam section through the beam and notched 6x6 post. Align your holes 2" from the top and bottom and edge of the beam.
Use a socket ratchet to tighten the 1/2" x 6" thrubolts from one side of each beam section through the beam and notched post. Use washers to protect the beam from overtightening. You may also use 8" long thrubolts.
This is a finished view of the beam splice over a support post. Notice how both sections of the beam are level.
Deck Joist Water Protection
Learn about a technique used by many pro builders for wrapping deck framing lumber with a waterproof barrier to prevent corrosion and rot.
Decking Patterns
Installing your decking at a 45-degree angle is a popular style for decks. This can be done to reduce decking seams or just for appearance.
More Helpful Resources
Explore Articles by Topic
Footings
Information related to installing frost footings for decks
Framing
Learn structural framing methods
Decking
Learn about wood and composite decking materials
Stairs
An in-depth look at the complex issue of how to build stairs
Railings
How to install guardrails and handrails to meet IRC code
Features
An overview on water drainage, benches, planters and lights
Design
The basics of deck design
Planning
Learn about permits and working with contractors
Porches & Patios
Build a covered deck to enjoy all seasons
Ledger
Proper attachment techniques
Care
Maintain your deck to maintain your investment
Materials
An overview on water drainage, benches, planters and lights
How to Splice a Deck Beam Over a Support Post
It is always best to use a continuous beam without seams for higher strength. Dimensional lumber is readily available in lengths up to 20' which should accommodate a seamless beam for most applications. However, if your span is greater than 20' (like the image below) you will likely need to splice some boards to form a beam. In order to do this you should overlap the individual parts of the beam so they are staggered if possible. It is best to have one continuous board over a post allowing one joint to fall on top of the post. Overlapping seams integrates strength and prevents fracturing along seams throughout the length of the beam. Always split a beam over a post.
Plan ahead and layout the beam on the ground over the footings before installation. For instance you could use 2-2x10x10's and 2-2x10x20's to form a 30' beam with one seam set above two intermediate posts. You can also use hardware applications like strap ties or nailing plates to further secure the connection. Because these connectors are not particularly attractive you will probably want to conceal them behind fascia or on the interior side of the beam.
When attaching the first half of the beam to the notched 6x6 support post screw through the center of the 2x10. This will hold the 2x10 in place until you install the second 2x10 piece of the beam.
Drill 2 thru holes on the edges of each beam section through the beam and notched 6x6 post. Align your holes 2" from the top and bottom and edge of the beam.
Use a socket ratchet to tighten the 1/2" x 6" thrubolts from one side of each beam section through the beam and notched post. Use washers to protect the beam from overtightening. You may also use 8" long thrubolts.
This is a finished view of the beam splice over a support post. Notice how both sections of the beam are level.
Deck Joist Water Protection
Learn about a technique used by many pro builders for wrapping deck framing lumber with a waterproof barrier to prevent corrosion and rot.
Decking Patterns
Installing your decking at a 45-degree angle is a popular style for decks. This can be done to reduce decking seams or just for appearance.
Installing Composite Decking
Learn about how to install composite decking. Topics include expansion and contraction issues and hidden fastener systems.
Best Hidden Fasteners for Decking
Hidden fasteners create a clean deck surface and can be used with composite, wood and other materials. Learn about hidden deck fasteners at Decks.com.
Explore Articles by Topic
Footings
Information related to installing frost footings for decks
Framing
Learn structural framing methods
Decking
Learn about wood and composite decking materials
Stairs
An in-depth look at the complex issue of how to build stairs
Railings
How to install guardrails and handrails to meet IRC code
Features
An overview on water drainage, benches, planters and lights
Design
The basics of deck design
Planning
Learn about permits and working with contractors
Porches & Patios
Build a covered deck to enjoy all seasons
Ledger
Proper attachment techniques
Care
Maintain your deck to maintain your investment
Materials
An overview on water drainage, benches, planters and lights
More Helpful Resources
Source: https://www.decks.com/how-to/articles/how-to-splice-a-deck-beam-over-a-support-post
0 Response to "Build 30 Ft Continuous Beam From 2x Lumber"
Post a Comment